JLT PERFORMANCE COLD AIR INTAKE KIT FOR 2012-2020 CHEROKEE SRT 6.4L!  NO TUNE REQUIRED FOR AWESOME LOOK AND SOUND!  This kit includes an ABS heat shield that has a opening in the front to grab fresh air from the grille/headlight area and also seals to the hood. Our air filter is a custom built design made by S&B. It has a built in bell mouth for super smooth and fast air flow as well as huge 1" deep pleats for more surface area than filters that look much bigger. The intake tube is roto molded plastic with a huge 5" filer opening for superior airflow and NO heat soak like metal tubes.With a mouth of 4" at the throttle body end, it is ready for any larger throttle bodies that may come in the future. FINISHStandard finish is an OEM looking black textured plastic. HEAT SHIELDIncludes our large ABS plastic heat shield to block engine heat at idle and low speed.It uses a large area to make sure the filter has tons of cool air and uses the factory fresh air inlet from the bumper to keep temps cool as stock KIT INCLUDES:• JLT Roto Molded Plastic Intake Tube• Silicone Reducer• 5x7 S&B powerstack Air Filter• ABS Heat Shield• HD Clamps, all needed hardware GAINS AND TESTING18-22 RWHP & 18-22 RWTQ are typical with this kit. TUNINGNo tuning required EASY INSTALLThe design, detailed instructions and online video (see below) helps make this an easy install (see Instructions & Videos tabs to download / view). AIR FILTER OPTIONS - OIL OR DRYWe use only the best air filters made by S&B to our specifications.For years we only used oiled filters, but dry filter technology has been proven and is now a popular option. Should I choose a Dry Disposable or Cotton Oiled Filter?Since you are not sacrificing performance with either choice, the decision comes down to would you rather throw away the filter or clean it. Dry: Comparable airflow to oiled cotton filters with the same great protection.Last for up to 30,000 miles of highway driving. Extend the life of the filter using compressed air. Oil: Oiled filters can last forever as long as you properly clean and re-oil it.Oil filters are available in red or blue and Dry filters are white. MAINTENANCETo properly clean your oil filter, we recommend the S&B Precision II Cleaning & Oiling Kit.*TIP* by purchasing a 2nd air filter you can simply swap filters when it's time to clean it and not be rushed. Clean the first filter and it's ready when it's time to change again. JLT Pre-Filters are now available for most intake kits we carry, these filters are made for us by Outerwears, these prefilters are water repellent. They will increase your filter life and cut down on your cleaning intervals!

Applications this kit fits: 2011-2021 Dodge Challenger 6.4L (Non-shaker cars only)2011-2021 Dodge Charger 6.4L2011-2020 Chrysler 300 SRT 6.4L JLT Performance has completely redesigned this kit for 2018 With the development and gains of the new Hellcat kit, we decided to make some improvements to the 2011-20 6.4 Hemi car intake. This kit includes a fully Roto Molded airbox that has a opening in the front to grab fresh air from the grille/headlight area and also seals to the hood. We feel this is the key component that puts our kit well above the rest. The JLT filter is a custom built design made by S&B. It has a built in bell mouth for super smooth and fast air flow as well as huge 1" deep pleats for more surface area than filters that look much bigger. The intake tube is roto molded plastic with a huge 5" filer opening for superior airflow and NO heat soak like metal tubes.With a mouth of 4" at the throttle body end, it is ready for any larger throttle bodies that may come in the future. FINISH OPTIONSStandard finish is an OEM looking black textured plastic. HEAT SHIELDIncludes new roto molded plastic heat shield to block engine heat at idle and low speed.It uses a large area to make sure the filter has tons of cool air. KIT INCLUDES:• JLT Black Textured Plastic Intake Tube• Silicone Reducer• 5x7 S&B Powerstack Air Filter• Roto molded Heat Shield• 4-3.5" silicone reducer• HD Clamps, all needed hardware GAINS AND TESTING10-15 RWHP & 10-15 RWTQ are typical with this kit on a stock 6.4JLT have seen 18-20 RWHP and RWTQ on a 6.4 with cam and headers. TUNINGNo tuning required EASY INSTALLThe design, detailed instructions and online video helps make this an easy install  AIR FILTER OPTIONS - OIL OR DRYWe use only the best air filters made by S&B to our specifications.For years we only used oiled filters, but dry filter technology has been proven and is now a popular option. Should I choose a Dry Disposable or Cotton Oiled Filter?Since you are not sacrificing performance with either choice, the decision comes down to would you rather throw away the filter or clean it. Dry: Comparable airflow to oiled cotton filters with the same great protection.Last for up to 30,000 miles of highway driving. Extend the life of the filter using compressed air. Oil: Oiled filters can last forever as long as you properly clean and re-oil it.Oil filters are available in red or blue and Dry filters are white. MAINTENANCETo properly clean your oil filter, we recommend the S&B Precision II Cleaning & Oiling Kit.*TIP* by purchasing a 2nd air filter you can simply swap filters when it's time to clean it and not be rushed. Clean the first filter and it's ready when it's time to change again. JLT Pre-Filters are now available for most intake kits we carry, these filters are made for us by Outerwears, these prefilters are water repellent. They will increase your filter life and cut down on your cleaning intervals! 

ALL NEW, JLT Cold Air Intake for 2018-2020 Jeep TrackHawk.  Bad to the Bone all on it's own. *Now fits 2020 Trackhawks! This kit includes an ABS heat shield that has a opening in the front to grab fresh air from the grille/headlight area and also seals to the hood. Our air filter is a custom built design made by S&B. It has a built in bell mouth for super smooth and fast air flow as well as huge 1" deep pleats for more surface area than filters that look much bigger. The intake tube is roto molded plastic with a huge 5" filer opening for superior airflow and NO heat soak like metal tubes.With a mouth of 4.5" at the throttle body end, it is ready for any larger throttle bodies that may come in the future. FINISHStandard finish is an OEM looking black textured plastic. HEAT SHIELDIncludes our large ABS plastic heat shield to block engine heat at idle and low speed.It uses a large area to make sure the filter has tons of cool air and uses the factory fresh air inlet from the bumper to keep temps cool as stock KIT INCLUDES:• JLT Roto Molded Plastic Intake Tube• Silicone Reducer• 5x7 S&B Powerstack Air Filter• ABS Heat Shield• HD Clamps, all needed hardware GAINS AND TESTING30-35 RWHP & 20-25 RWTQ are typical with this kit. TUNINGNo tuning required EASY INSTALLThe design, detailed instructions and online video (see below) helps make this an easy install (see Instructions & Videos tabs to download / view). AIR FILTER OPTIONS - OIL OR DRYWe use only the best air filters made by S&B to our specifications.For years we only used oiled filters, but dry filter technology has been proven and is now a popular option. Should I choose a Dry Disposable or Cotton Oiled Filter?Since you are not sacrificing performance with either choice, the decision comes down to would you rather throw away the filter or clean it. Dry: Comparable airflow to oiled cotton filters with the same great protection.Last for up to 30,000 miles of highway driving. Extend the life of the filter using compressed air. Oil: Oiled filters can last forever as long as you properly clean and re-oil it.Oil filters are available in red or blue and Dry filters are white. MAINTENANCETo properly clean your oil filter, we recommend the S&B Precision II Cleaning & Oiling Kit.*TIP* by purchasing a 2nd air filter you can simply swap filters when it's time to clean it and not be rushed. Clean the first filter and it's ready when it's time to change again. JLT Pre-Filters are now available for most intake kits we carry, these filters are made for us by Outerwears, these prefilters are water repellent. They will increase your filter life and cut down on your cleaning intervals!

JLT Cold Air Intake For 2011-20 Durango and Jeep Grand Cherokee 5.7L  Help your HEMI get all the cold air it can eat!  Looks great, sounds great with NO TUNE REQUIRED This kit includes a roto-molded heat shield that has an opening in the front to grab fresh air from the grille/headlight area and also seals to the hood. Our air filter is a custom-built design made by S&B. It has a built-in bellmouth for super smooth and fast airflow as well as huge 1" deep pleats for more surface area than filters that look much bigger. The intake tube is roto-molded plastic with a huge 5" filer opening for superior airflow and NO heat soak like metal tubes. With a mouth of 4" at the throttle body end, it is ready for any larger throttle bodies that may come in the future. HEAT SHIELDIncludes our large ABS plastic heat shield to block engine heat at idle and low speed. It uses a large area to make sure the filter has tons of cool air and uses the factory fresh air inlet from the bumper to keep temps cool. KIT INCLUDES:• JLT Roto Molded Black Textured Plastic Intake Tube• Silicone Reducer• 5x7 S&B Air Filter Red Oil• JLT Roto Molded Heat Shield• HD Clamps, all needed hardware GAINS AND TESTING6-12 RWHP &  RWTQ are typical with this kit. TUNINGNo tuning required

The company that has brought such benchmark setting systems to the modern Mopar platform such as the True V2 and Hellcat Intake now offers something for the newly released Jeep Track Hawk community of owners. Like many of the LMI air intake systems, the LMI Track Hawk Intake will surely set a high benchmark for the Track Hawk!!! Independently tested to show a REALISTIC 18-22 rwhp increase over stock airbox (Tests conducted by two separate independent Mopar specialists) Track tested to show .1 - .2 tenth improvements over stock airbox Handmade from 100% real carbon fiber construction for superior heat characteristics Proprietary fabrication process resulting in a smooth inner surface to ensure optimal air flow "Funnel" shape with 6" opening smoothly transitioning to 4.5" to help speed airflow and decrease restriction Large 6" diameter S&B filter with 8 layer protection (cleanable oil type) High quality silicon coupler ensuring smooth transition to throttle body High quality stainless T-bolt clamps provided, Drilled for IAT fitting with a rubber grommet for secure fit and seal Laser cut rain shield with superior wrinkle finish powder coat and machined Legmaker logo Water repellent pre-filter to ensure maximum protection of filter from moisture and debris All necessary hardware and instructions for DIY install ZERO cutting or modifications needed to install.